Simulation of Cutting Force During High Speed End Milling of Inconel 718

  • H. N. Ganesan
  • M. S. Kasim
  • R. Izamshah
  • T.J.S. Anand
  • N. H. Harun
  • S.A. Sundi

Abstract


This study aims to investigate the effect of cutting parameters on cutting force by simulation of high speed end milling of Inconel 718. The simulations were carried out using Deform 3D software. TiAlN/AlCrN-coated carbide inserts were employed as the cutting tool for the machining simulation. The milling cutting parameters were cutting speed (100-140 m/min), feed rate (0.1-0.2 mm/tooth) and axial depth of cut (0.5 – 1.0 mm). Response surface methodology (RSM) was used to determine the optimum cutting parameter in order to yield minimum cutting force. The minimum cutting force reported was 38.89 N, under the optimal parameter settings of Vc = 120.58 m/min, fz = 0.13mm/tooth and ap = 0.98mm.

Downloads

Download data is not yet available.

References

A. Li, J. Zhao, G. Zheng and Z. Pei, "Machined surface roughness and chip morphology in high speed side milling of Inconel 718” in Consumer Electronics, Communications and Networks, Xianning, 2011, pp. 442-445.

S. Dolinšek, B. Šuštaršič and J. Kopač, "Wear mechanisms of cutting tools in high-speed cutting processes”, Wear, vol. 250, no. 1-12, pp. 349-356, 2001.

E. Leigh, J. Tlusty and J. Schuelle, “Applying High-Speed Machining Techniques on Rotor Grip Configuration”, in American Helicopter Society 55th Annual Forum, Quebec, Canada, 1999. pp. 1437-1452.

D. G. Thakur, B. Ramamoorthy and L. Vijayaraghavan, “Study on the machinability characteristics of superalloy Inconel 718 during high speed turning”, Materials & Design, vol. 30, no. 5, pp. 1718-1725, 2009.

A. Devillez, F. Schneider, S. Dominiak, D. Dudzinsk and D. Larrouquere, “Cutting forces and wear in dry machining of Inconel 718 with coated carbide tools”, Wear, vol. 262, no. 7-8, pp. 931-942, 2007.

E. Kose, A. Kurt and U. Seker, “The effects of the feed rate on the cutting tool stresses in machining of Inconel 718”, Journal of Materials Processing Technology, vol.196, no. 1-3, pp. 165-173, 2008.

L. Qian and M. R. Hossan, “Effect on cutting force in turning hardened tool steels with cubic boron nitride inserts,” Journal of Materials Processing Technology, vol. 191, no. 1-3, pp. 274–278, 2007.

M. S. Kasim, C. H. C. Haron, J. A. Ghani, A. I. Gusri, M. Z. A. Yazid and M. A. Sulaiman, “Tool life of TiAlN PVD coated carbide tool in high-speed end milling untreated Inconel 718 under minimum quantity lubrication condition”, Sains Malaysiana, vol. 42, no. 12, pp. 1721-1726, 2013.

O. Colak, “Investigation on machining performance of Inconel 718 under high pressure cooling conditions”, Strojniški vestnik-Journal of Mechanical Engineering, vol. 58, no. 11, pp. 683-690, 2012.

S. L. Soo, D. K. Aspinwall and R. C. Dewes, “3D FEM modelling of the cutting of Inconel 718”, Journal of Materials Processing Technology, vol. 150, no. 1-2, pp. 116-123, 2004.

S. Zhang, J. F. Li and Y. W. Wang, “Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions”, Journal of Cleaner Production, vol. 32, pp. 81–87, 2012.

M. A. Hadi, C. H. C. Haron and M. S. Kasim,”Investigation on wear behavior and chip formation during up-milling and down-milling operations for Inconel 718”, Jurnal Teknologi, vol. 66, no. 3, pp. 15-21, 2014.

K. Komvopoulos and S.A. Erpenbeck, “Finite element modelling of orthogonal metal cutting”, Journal of Engineeering for Industry, vol. 113, no. 3, pp. 253-267, 1991.

W. H. Lai, “Modeling of cutting forces in end milling operations”, Journal of Science and Engineering, vol. 3, no. 1, pp. 15-22, 2000.

Y. S. Liao, H. M. Lin and J. H. Wang, “Behaviors of end milling Inconel 718 superalloy by cemented carbide tools”, Journal of Materials Processing Technology, vol. 201, no. 1-3, pp. 460-465, 2008.

How to Cite
Ganesan, H. N., Kasim, M. S., Izamshah, R., Anand, T., Harun, N. H., & Sundi, S. (1). Simulation of Cutting Force During High Speed End Milling of Inconel 718. Journal of Advanced Manufacturing Technology (JAMT), 12(1(1), 383-392. Retrieved from https://jamt.utem.edu.my/jamt/article/view/4007
Section
Articles